you should take an external source
like another synth or cd player
and plug it into the mixin
and then try playing notes to hear the sound
if you hold the waveform switch in the middle
it should silence the vco
you can only hear things when the vca is triggered
which is why you need to play notes to hear it
Mix in go through VCF?
Moderators: altitude, adafruit_support_bill, adafruit, phono, hamburgers
Please be positive and constructive with your questions and comments.
- isak
- Posts: 835
- Joined: Wed May 27, 2009 3:54 pm
Re: Mix in go through VCF?
mmm..i understand.
and if i'll do it like u said here..
i'll give it a try unless u'r saying what i did is better.
and if i'll do it like u said here..
then i will not have to trigger anything right?youre going to need a capacitor and a resistor
solder a wire from ioboard j7 pin3 to a 47k resistor
you may want to experiment with resistor values
and the the other end of the resistor should go to a 10uF capacitor
this will be an electrolytic capacitor
so be sure that the resistor connects to the negative end of the capacitor
then solder the positive end of the capacitor
to the r70 and c17 juncture
whichever is easiest to get to is fine
i'll give it a try unless u'r saying what i did is better.
-
- Posts: 3155
- Joined: Fri Feb 17, 2006 5:35 am
Re: Mix in go through VCF?
the vcf goes into the vca
so unless you bypass the vca
you will always have to trigger the vca
to hear the sound
is it working now
so unless you bypass the vca
you will always have to trigger the vca
to hear the sound
is it working now
- isak
- Posts: 835
- Joined: Wed May 27, 2009 3:54 pm
Re: Mix in go through VCF?
yes thank you, but i wanted it to be independent.. like to be able to control the cutoff only when the x0x is on, no sound playing.
never mined i'll tell the owner of the x0x that this is it.
no magic mushroom around
ayayayayayay Amsterdam
never mined i'll tell the owner of the x0x that this is it.
no magic mushroom around
ayayayayayay Amsterdam
-
- Posts: 39
- Joined: Sun Jul 08, 2007 11:37 pm
Re: Mix in go through VCF?
It is totally possible actually, you could use the vca/gate on mod to leave the gate open forever.
- isak
- Posts: 835
- Joined: Wed May 27, 2009 3:54 pm
Re: Mix in go through VCF?
yes your right you can do that, but... then u'll get always sound from the x0x.
-
- Posts: 151
- Joined: Wed Jul 11, 2007 2:02 pm
Re: Mix in go through VCF?
If you don't replace the waveform switch with a on-off-on switch instead of the on-on?isak wrote:yes your right you can do that, but... then u'll get always sound from the x0x.
- altitude
- Posts: 995
- Joined: Wed May 11, 2005 5:17 pm
Re: Mix in go through VCF?
That would turn the OSC feed into the VCF, it would not do anything about the gate and env. If you want to just run audio through the filter, you must do the gate/env mod. I just have mine as a DPDT switch with 12V as a common input and the two outs the the diodesxlarge wrote:If you don't replace the waveform switch with a on-off-on switch instead of the on-on?isak wrote:yes your right you can do that, but... then u'll get always sound from the x0x.
-
- Posts: 3155
- Joined: Fri Feb 17, 2006 5:35 am
Re: Mix in go through VCF?
you could also
send vcf mixin on the tip
and patch vcf out to the ring
it wouldnt be perfect
but would be pretty easy
send vcf mixin on the tip
and patch vcf out to the ring
it wouldnt be perfect
but would be pretty easy
Please be positive and constructive with your questions and comments.