Hi
I am in the process of writing some software for a full color pov project.
I was just wondering if somebody could download it and try loading different images to trip it up.
There is not much there yet but it is work in progress.
The left hand window is the original image and the right hand window is the simulation like spokepov.
If you click on the right hand pic you can zoom in.
http://www.rmtucker.f2s.com/weardalecnc ... CarPov.zip
Regards
Mark
http://www.weardalecnccarving.co.uk
Color Pov Software
Moderators: adafruit_support_bill, adafruit
Please be positive and constructive with your questions and comments.
-
- Posts: 24
- Joined: Mon Oct 09, 2006 11:02 am
I have just uploaded v1.01
I have added a few more buttons which are self explanitory(i think).
Same link as above.
I will carry on updating to the link above when i update so keep re-downloading.
Regards
Mark
I have added a few more buttons which are self explanitory(i think).
Same link as above.
I will carry on updating to the link above when i update so keep re-downloading.
Regards
Mark
Last edited by rmtucker on Tue Oct 10, 2006 12:34 pm, edited 1 time in total.
-
- Posts: 24
- Joined: Mon Oct 09, 2006 11:02 am
I have just uploaded v1.02 which now has click to zoom in both windows,also added number of led's,and change buttons to a more useable configuration.
I am hoping to add number of colors next so that it can be used for minipov and spokepov also.(with your permission Ladyada?)
After that i am looking to add the choice of horizontal or vertical spinning.
Regards
Mark
http://www.weardalecnccarving.co.uk
I am hoping to add number of colors next so that it can be used for minipov and spokepov also.(with your permission Ladyada?)
After that i am looking to add the choice of horizontal or vertical spinning.
Regards
Mark
http://www.weardalecnccarving.co.uk
-
- Posts: 24
- Joined: Mon Oct 09, 2006 11:02 am
Just uploaded v1.03 which gets rid of the buttons and adds a menu,also zoom on both windows.
Simple setup data for # of leds,led dia,and hub radius (ie dist from ctr to first led).
Starting on the minipov section now.This will allow you to enter text or bitmap and output the Data ready to Send to the Microcontroller.
Sample chips turned up from maxim so i can also start on the hardware for the car wheel pov.
Regards
Mark
http://www.weardalecnccarving.co.uk
Simple setup data for # of leds,led dia,and hub radius (ie dist from ctr to first led).
Starting on the minipov section now.This will allow you to enter text or bitmap and output the Data ready to Send to the Microcontroller.
Sample chips turned up from maxim so i can also start on the hardware for the car wheel pov.
Regards
Mark
http://www.weardalecnccarving.co.uk
-
- Posts: 24
- Joined: Mon Oct 09, 2006 11:02 am
v1.04 uploaded.
Gets rid of a bug which crept in and distorted the simulation.
Added a choice for the number of rotary pixels.
files are now saved with an ext
(cpv = carpov file,spv=spokepov,mpv=minipov).
I have also added a menu at start for carpov,spokepov,minipov.
The latter 2 are not working yet,still working on them.
I am adding the possibility into minipov for bitmaps or text or a mixture.
I will add the same function into the others.
Any comment or ideas are welcome.
Oh my minipov turned up from ladyada this morning so i will be able to put the program into practice.
I will order a spokepov next as soon as finances allow,so i can also test the software on that.
I am still waiting of hardware for the carpov project.
Regards
Mark
http://www.weardalecnccarving.co.uk
Gets rid of a bug which crept in and distorted the simulation.
Added a choice for the number of rotary pixels.
files are now saved with an ext
(cpv = carpov file,spv=spokepov,mpv=minipov).
I have also added a menu at start for carpov,spokepov,minipov.
The latter 2 are not working yet,still working on them.
I am adding the possibility into minipov for bitmaps or text or a mixture.
I will add the same function into the others.
Any comment or ideas are welcome.
Oh my minipov turned up from ladyada this morning so i will be able to put the program into practice.
I will order a spokepov next as soon as finances allow,so i can also test the software on that.
I am still waiting of hardware for the carpov project.
Regards
Mark
http://www.weardalecnccarving.co.uk
-
- Posts: 3
- Joined: Fri Sep 15, 2006 10:51 am
COLORED IMAGES
Do any body got schematics for Car POV?
-
- Posts: 24
- Joined: Mon Oct 09, 2006 11:02 am
Ver 1.06 Uploaded
This version now has Carpov,Spokepov,minipov all functioning.
When in spokepov or minipov mode,any bitmap you load will be automatically turned into a monochrome bitmap ready to simulate.
In the setup screen you can now choose to simulate in two modes.
1. A Radiating grid like spokepov.
2. Round pixels
If i get enough feedback on this i will add the output to enable programming of minipov and spokepov.
The next version will have text enabled also.
Regards
Mark
http://www.weardalecnccarving.co.uk
This version now has Carpov,Spokepov,minipov all functioning.
When in spokepov or minipov mode,any bitmap you load will be automatically turned into a monochrome bitmap ready to simulate.
In the setup screen you can now choose to simulate in two modes.
1. A Radiating grid like spokepov.
2. Round pixels
If i get enough feedback on this i will add the output to enable programming of minipov and spokepov.
The next version will have text enabled also.
Regards
Mark
http://www.weardalecnccarving.co.uk
-
- Posts: 24
- Joined: Mon Oct 09, 2006 11:02 am
Ver 1.07 Uploaded
This version has a few snags which i am still working on (text etc)
But it also allows choice of led color in spokepov/minipov modes.
Just click on the color box in setup and you can choose.
Be careful with text as i said it's buggy.
I have not had any feedback so i can only assume no one is downloading, maybe when i enable the output?.
I have had the output working on my minipov so it does work.
Thinking about adding animation in also if anyone is interested.
Regards
Mark
http://www.weardalecnccarving.co.uk
This version has a few snags which i am still working on (text etc)
But it also allows choice of led color in spokepov/minipov modes.
Just click on the color box in setup and you can choose.
Be careful with text as i said it's buggy.
I have not had any feedback so i can only assume no one is downloading, maybe when i enable the output?.
I have had the output working on my minipov so it does work.
Thinking about adding animation in also if anyone is interested.
Regards
Mark
http://www.weardalecnccarving.co.uk
-
- Posts: 2
- Joined: Fri Jul 21, 2006 10:44 am
I don't like me too's
but.. Me too
Last edited by fazgood on Thu Oct 26, 2006 11:30 pm, edited 1 time in total.
-
- Posts: 46
- Joined: Sun Jul 09, 2006 2:00 pm
-
- Posts: 24
- Joined: Mon Oct 09, 2006 11:02 am
Hi Guys
I will try and clarify what i am doing.
1. To produce a program that simulates and outputs a 'c' program ready to send to the minipov using avrdude and make.
2. To Simulate and output to spokepov (I have not got one so i am not sure how this works.)
3. To simulate and output to a full color version of spokepov that i am in the process of designing.
I am in the process of re-writing carpov but when i release it,it will allow you to output to minipov for a start.
Regards
Mark
http://www.weardalecnccarving.co.uk
I will try and clarify what i am doing.
1. To produce a program that simulates and outputs a 'c' program ready to send to the minipov using avrdude and make.
2. To Simulate and output to spokepov (I have not got one so i am not sure how this works.)
3. To simulate and output to a full color version of spokepov that i am in the process of designing.
I am in the process of re-writing carpov but when i release it,it will allow you to output to minipov for a start.
Regards
Mark
http://www.weardalecnccarving.co.uk
-
- Posts: 24
- Joined: Mon Oct 09, 2006 11:02 am
V1.08 Uploaded
There are a few changes here :-
1.The choice of simulation (radiating grid / round pixels) has gone
there is now only round pixels,more pleasing to the eye.
2.Text now working but please ensure you push the paste button else the text will not be saved or output.
3.Minipov output is now active,it outputs a 'c' file ready to make into a hex file and program straight into the minipov.
I have tested this tonight on my minipov and it works great (no more 0100010 etc).
I output the file as marks.c then tried MAKE marks.hex and it did not work at first,so i changed it's name to mypov.c and it worked first time.
I am not sure why this is but if somebody has any suggestions let me know.
Regards
Mark
http://www.weardalecnccarving.co.uk
There are a few changes here :-
1.The choice of simulation (radiating grid / round pixels) has gone
there is now only round pixels,more pleasing to the eye.
2.Text now working but please ensure you push the paste button else the text will not be saved or output.
3.Minipov output is now active,it outputs a 'c' file ready to make into a hex file and program straight into the minipov.
I have tested this tonight on my minipov and it works great (no more 0100010 etc).
I output the file as marks.c then tried MAKE marks.hex and it did not work at first,so i changed it's name to mypov.c and it worked first time.
I am not sure why this is but if somebody has any suggestions let me know.
Regards
Mark
http://www.weardalecnccarving.co.uk
Please be positive and constructive with your questions and comments.