Check my joints? DIY SMD stencil w/ *pictures*

Chat about pick and place machines, reflow ovens, assembly techniques and other SMT tips & trix

Moderators: adafruit_support_bill, adafruit

Please be positive and constructive with your questions and comments.
Locked
User avatar
george_graves
 
Posts: 342
Joined: Thu Feb 26, 2009 2:10 am

Check my joints? DIY SMD stencil w/ *pictures*

Post by george_graves »

So...I made my own SMD stencil - all from thing I found at the hardware store. I'll be doing a full (video?)write up once I iron out some kinks - so bear with me.

Pictures are below - but before you forget - please let me know what you think of my joints. It looks like there might be a tad too much solder? Please let me know what you think of it. Too much on the toe?

Some surface mount stuff to test
Image

Image

It's really hard to convey to people how small this stuff is.
Image

Some test boards - they do nothing. Just testing pad size and the effects of surface tension, pad width and trace location on centering parts during reflow. Trying different pad sizes, ect. And I hope that I can sneak a trace between the pads of an 0805 - that would be nice.
Image

I'm a sneaky little bastard.
Image

Paste laid up. It came out perfect I think - might need to adjust the stencil for the amount, but looks great.
Image

Image

ready for reflow
Image

Finished. Almost perfect. A bit too much solder? My 10 mil traces don't look bad either. That's insane.
Image

Another look at the heel. How's it look?
Image

Image

adafruit
 
Posts: 12151
Joined: Thu Apr 06, 2006 4:21 pm

Re: Check my joints? DIY SMD stencil w/ *pictures*

Post by adafruit »

nice fillet!

User avatar
alphatronique
 
Posts: 231
Joined: Fri Jun 25, 2010 8:30 am

Re: Check my joints? DIY SMD stencil w/ *pictures*

Post by alphatronique »

Hi

nice stencil :mrgreen:

solder past volume was ok for 1.27 mm soic and 0805
you may will need to reduce it for do finer pitch and use 5mil think brass

did you etch brass whit ferric chloride ?

Best regard

skylen
 
Posts: 56
Joined: Fri Sep 04, 2009 5:54 pm

Re: Check my joints? DIY SMD stencil w/ *pictures*

Post by skylen »

Wow, very nice work. I would love to be able to achieve that quality in my lab. Can you comment on the following:
  • What is your PCB etching process (impressive quality at 10 mil traces!) -- did you use toner transfer? What kind of paper? What make/model of printer? I have used the Pulsar Pro FX Toner Transfer Paper/GreenTRF which seemed a great improvement in consistency from using photo paper. However, I'm having toner density and quality problems with my laser printers that are giving me all kinds of problems right now.
  • How you made the stencil? (what did you etch that you found at the hardware store? how did you etch it?)
  • What's your reflow process? Toaster over? Skillet/hot plate? I recently got a cheap hot plate to try out.

User avatar
george_graves
 
Posts: 342
Joined: Thu Feb 26, 2009 2:10 am

Re: Check my joints? DIY SMD stencil w/ *pictures*

Post by george_graves »

I have a few more tests then I'll do a full write up with parts,how to, and maybe a video.

skylen
 
Posts: 56
Joined: Fri Sep 04, 2009 5:54 pm

Re: Check my joints? DIY SMD stencil w/ *pictures*

Post by skylen »

OK, I'll definitely be looking forward to that. Thanks!

Agent24
 
Posts: 307
Joined: Sun Jan 24, 2010 6:48 am

Re: Check my joints? DIY SMD stencil w/ *pictures*

Post by Agent24 »

These look very nice :)

I have yet to try anything like this so far but its nice to know with some care you can get good results like this.

Currently the smallest traces I have done are 20mil (or 0.5mm), but they have come out near-perfect so I think even 10mil shouldn't have much of a problem for me.

I see yours do have wavy edges, do you know what caused this?

User avatar
randyhall
 
Posts: 5
Joined: Wed Feb 09, 2011 3:56 am

Re: Check my joints? DIY SMD stencil w/ *pictures*

Post by randyhall »

I have a few more tests then I'll do a full write up with parts,how to, and maybe a video.
I definitely want to see how the stencil was made. It's sick how well it worked.

--R

Philly
 
Posts: 57
Joined: Sun Jun 20, 2010 7:53 am

Re: Check my joints? DIY SMD stencil w/ *pictures*

Post by Philly »

Im guessing it was etched the same way as copper clad, but with the back of the brass covered.

User avatar
rayshobby
 
Posts: 6
Joined: Fri Oct 14, 2011 11:01 am

Re: Check my joints? DIY SMD stencil w/ *pictures*

Post by rayshobby »

Perhaps the process is similar to this one?
http://rayshobby.net/blog/?p=1246

User avatar
xl97
 
Posts: 201
Joined: Mon Jul 27, 2009 12:51 pm

Re: Check my joints? DIY SMD stencil w/ *pictures*

Post by xl97 »

bump... (lol)

what ever happened to this 'write up'?? :lol:


looking for hwo the stencil was made too!..

(might be better than ordering a kapton once each time..!!!!)

bearmos
 
Posts: 9
Joined: Tue Feb 14, 2012 11:44 pm

Re: Check my joints? DIY SMD stencil w/ *pictures*

Post by bearmos »

Nice work. The heals of the IC's look perfect, although I do agree the toe of one may have a little too much solder on it (but only in one of the shots). In the rest of the pics the toes look fine.

Also curious as to what methods you're using for etching (first guess is photo transfer for the PCB from the looks of the traces) - it certainly looks more respectable than anything I've done with photo transfer!

User avatar
adafruit_support_mike
 
Posts: 67446
Joined: Thu Feb 11, 2010 2:51 pm

Re: Check my joints? DIY SMD stencil w/ *pictures*

Post by adafruit_support_mike »

*Nice* work.

FWIW, I've gotten two 10 mil traces between the pads of an 0805 without too much pain:

Image
It isn't nearly as pretty as yours since it's hand-soldered, but it is a toner transfer job. The trick is to leave 50-60 mil between the 0805 pads.

Locked
Please be positive and constructive with your questions and comments.

Return to “SMT (Surface Mount Tech)”