I can not get the PiTFT Mini Kit - 320x240 2.8" TFT to work. I am following the http://learn.adafruit.com/adafruit-pitf ... i/overview on a freshly installed 2013-09-25-wheezy-raspbian OS. All of the software downloads and installs fine in the first part of the tutorial. When you get to the point where you issue the commands to load the screen driver and it should flash from black to white then you should see some console text, nothing happens.
I have checked the screen flex ribbon cable for good seating, still nothing. What are my next steps to determining if I have a bad screen, or something else?
PiTFT Mini Kit - 320x240 2.8" TFT Problems
Moderators: adafruit_support_bill, adafruit
Forum rules
Talk about Adafruit Raspberry Pi® accessories! Please do not ask for Linux support, this is for Adafruit products only! For Raspberry Pi help please visit: http://www.raspberrypi.org/phpBB3/
Talk about Adafruit Raspberry Pi® accessories! Please do not ask for Linux support, this is for Adafruit products only! For Raspberry Pi help please visit: http://www.raspberrypi.org/phpBB3/
- tz1
- Posts: 32
- Joined: Sat Aug 01, 2009 11:26 pm
Re: PiTFT Mini Kit - 320x240 2.8" TFT Problems
What is the output when the fbtft_device loads? You can find this with 'dmesg | less". Are you connected directly?
Try reseating the display. Do you have anything else connected, and check your soldering work.
Try reseating the display. Do you have anything else connected, and check your soldering work.
- adafruit_support_mike
- Posts: 67485
- Joined: Thu Feb 11, 2010 2:51 pm
Re: PiTFT Mini Kit - 320x240 2.8" TFT Problems
Also try reseating the flex cable's connection to the socket on the PCB. It's easy to pull that slightly askew while moving the TFT, an almost impossible to see the difference between a clean connection and one that won't work.
- tbiddle
- Posts: 4
- Joined: Sun Feb 10, 2013 9:11 pm
Re: PiTFT Mini Kit - 320x240 2.8" TFT Problems
I have reseated the flex cable connection several times. Have have check the solder joints, and did a quick reheat to make sure no cold joints.
The fbtft_device does not load, or is recognized. I really do not know where to go from here.
Below I will post my dmesg:
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.6.11+ (smc@build-ssd) (gcc version 4.5.4 20120305 (prerelease) (GCC) ) #26 PREEMPT Tue Nov 26 18:19:51 SGT 2013
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr =00c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruc tion cache
[ 0.000000] Machine: BCM2708
[ 0.000000] cma: CMA: reserved 16 MiB at 1b000000
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 114688
[ 0.000000] free_area_init_node: node 0, pgdat c055c1b0, node_mem_map c060600 0
[ 0.000000] Normal zone: 896 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 113792 pages, LIFO batch:31
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 113792
[ 0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=656 b cm2708_fb.fbheight=416 bcm2708.boardrev=0xf bcm2708.serial=0x9e6c9cd7 smsc95xx.m acaddr=B8:27:EB:6C:9C:D7 sdhci-bcm2708.emmc_clock_freq=100000000 vc_mem.mem_base =0x1ec00000 vc_mem.mem_size=0x20000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115 200 kgdboc=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 eleva tor=deadline rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 448MB = 448MB total
[ 0.000000] Memory: 432132k/432132k available, 26620k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdc800000 - 0xff000000 ( 552 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdc000000 ( 448 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0502ef4 (5100 kB)
[ 0.000000] .init : 0xc0503000 - 0xc052454c ( 134 kB)
[ 0.000000] .data : 0xc0526000 - 0xc055c9e0 ( 219 kB)
[ 0.000000] .bss : 0xc055ca04 - 0xc0605e78 ( 678 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, N odes=1
[ 0.000000] NR_IRQS:394
[ 0.000000] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4 294967ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty1] enabled
[ 0.000956] Calibrating delay loop... 697.95 BogoMIPS (lpj=3489792)
[ 0.060125] pid_max: default: 32768 minimum: 301
[ 0.060588] Mount-cache hash table entries: 512
[ 0.061383] Initializing cgroup subsys cpuacct
[ 0.061443] Initializing cgroup subsys devices
[ 0.061475] Initializing cgroup subsys freezer
[ 0.061504] Initializing cgroup subsys blkio
[ 0.061643] CPU: Testing write buffer coherency: ok
[ 0.061968] hw perfevents: enabled with v6 PMU driver, 3 counters available
[ 0.062108] Setting up static identity map for 0x3b46d8 - 0x3b4734
[ 0.063597] devtmpfs: initialized
[ 0.078685] NET: Registered protocol family 16
[ 0.085100] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[ 0.086186] bcm2708.uart_clock = 0
[ 0.087579] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.087632] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.087667] mailbox: Broadcom VideoCore Mailbox driver
[ 0.087762] bcm2708_vcio: mailbox at f200b880
[ 0.087860] bcm_power: Broadcom power driver
[ 0.087897] bcm_power_open() -> 0
[ 0.087921] bcm_power_request(0,
[ 0.588604] bcm_mailbox_read -> 00000080, 0
[ 0.588643] bcm_power_request -> 0
[ 0.588668] Serial: AMBA PL011 UART driver
[ 0.588795] dev:f1: ttyAMA0 at MMIO 0x20201000 (irq = 83) is a PL011 rev3
[ 0.915559] console [ttyAMA0] enabled
[ 0.939538] bio: create slab <bio-0> at 0
[ 0.944622] SCSI subsystem initialized
[ 0.948693] usbcore: registered new interface driver usbfs
[ 0.954298] usbcore: registered new interface driver hub
[ 0.959907] usbcore: registered new device driver usb
[ 0.966205] Switching to clocksource stc
[ 0.970502] FS-Cache: Loaded
[ 0.973686] CacheFiles: Loaded
[ 0.988862] NET: Registered protocol family 2
[ 0.994116] TCP established hash table entries: 16384 (order: 5, 131072 bytes )
[ 1.001853] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 1.008640] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.015237] TCP: reno registered
[ 1.018488] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.024380] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 1.030999] NET: Registered protocol family 1
[ 1.035878] RPC: Registered named UNIX socket transport module.
[ 1.041929] RPC: Registered udp transport module.
[ 1.046652] RPC: Registered tcp transport module.
[ 1.051395] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.058502] bcm2708_dma: DMA manager at f2007000
[ 1.063289] bcm2708_gpio: bcm2708_gpio_probe c0533d98
[ 1.068730] vc-mem: phys_addr:0x00000000 mem_base=0x1ec00000 mem_size:0x20000 000(512 MiB)
[ 1.077970] audit: initializing netlink socket (disabled)
[ 1.083574] type=2000 audit(0.940:1): initialized
[ 1.220430] VFS: Disk quotas dquot_6.5.2
[ 1.224665] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.233821] FS-Cache: Netfs 'nfs' registered for caching
[ 1.240534] NFS: Registering the id_resolver key type
[ 1.245708] Key type id_resolver registered
[ 1.249907] Key type id_legacy registered
[ 1.254341] msgmni has been set to 876
[ 1.260415] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 52)
[ 1.268149] io scheduler noop registered
[ 1.272177] io scheduler deadline registered (default)
[ 1.277411] io scheduler cfq registered
[ 1.290584] Console: switching to colour frame buffer device 82x26
[ 1.300499] kgdb: Registered I/O driver kgdboc.
[ 1.307009] vc-cma: Videocore CMA driver
[ 1.312329] vc-cma: vc_cma_base = 0x00000000
[ 1.318299] vc-cma: vc_cma_size = 0x00000000 (0 MiB)
[ 1.324933] vc-cma: vc_cma_initial = 0x00000000 (0 MiB)
[ 1.340364] brd: module loaded
[ 1.349746] loop: module loaded
[ 1.354504] vchiq: vchiq_init_state: slot_zero = 0xdb000000, is_master = 0
[ 1.363466] Loading iSCSI transport class v2.0-870.
[ 1.370647] usbcore: registered new interface driver smsc95xx
[ 1.377987] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 1.590148] Core Release: 2.80a
[ 1.594563] Setting default values for core params
[ 1.600592] Finished setting default values for core params
[ 1.812456] Using Buffer DMA mode
[ 1.816950] Periodic Transfer Interrupt Enhancement - disabled
[ 1.823941] Multiprocessor Interrupt Enhancement - disabled
[ 1.830685] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 1.836194] Dedicated Tx FIFOs mode
[ 1.841817] dwc_otg: Microframe scheduler enabled
[ 1.842234] dwc_otg bcm2708_usb: DWC OTG Controller
[ 1.848391] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1
[ 1.856897] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000
[ 1.863641] Init: Port Power? op_state=1
[ 1.868726] Init: Power Port (0)
[ 1.873229] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.881391] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 1.889876] usb usb1: Product: DWC OTG Controller
[ 1.895855] usb usb1: Manufacturer: Linux 3.6.11+ dwc_otg_hcd
[ 1.902877] usb usb1: SerialNumber: bcm2708_usb
[ 1.909405] hub 1-0:1.0: USB hub found
[ 1.914495] hub 1-0:1.0: 1 port detected
[ 1.919895] dwc_otg: FIQ enabled
[ 1.919910] dwc_otg: NAK holdoff enabled
[ 1.919918] dwc_otg: FIQ split fix enabled
[ 1.919936] Module dwc_common_port init
[ 1.920161] Initializing USB Mass Storage driver...
[ 1.926542] usbcore: registered new interface driver usb-storage
[ 1.933808] USB Mass Storage support registered.
[ 1.939745] usbcore: registered new interface driver libusual
[ 1.947029] mousedev: PS/2 mouse device common for all mice
[ 1.954560] bcm2835-cpufreq: min=700000 max=700000 cur=700000
[ 1.961660] bcm2835-cpufreq: switching to governor powersave
[ 1.968493] bcm2835-cpufreq: switching to governor powersave
[ 1.975339] cpuidle: using governor ladder
[ 1.980600] cpuidle: using governor menu
[ 1.985674] sdhci: Secure Digital Host Controller Interface driver
[ 1.992998] sdhci: Copyright(c) Pierre Ossman
[ 1.998530] sdhci: Enable low-latency mode
[ 2.040501] mmc0: SDHCI controller on BCM2708_Arasan [platform] using platfor m's DMA
[ 2.050786] mmc0: BCM2708 SDHC host at 0x20300000 DMA 2 IRQ 77
[ 2.060043] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.072630] usbcore: registered new interface driver usbhid
[ 2.079533] usbhid: USB HID core driver
[ 2.089452] TCP: cubic registered
[ 2.096177] Initializing XFRM netlink socket
[ 2.103857] NET: Registered protocol family 17
[ 2.109729] Key type dns_resolver registered
[ 2.116490] Indeed it is in host mode hprt0 = 00021501
[ 2.125422] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
[ 2.151277] registered taskstats version 1
[ 2.158456] Waiting for root device /dev/mmcblk0p2...
[ 2.171110] mmc0: new high speed SDHC card at address 0007
[ 2.190541] mmcblk0: mmc0:0007 SD16G 14.9 GiB
[ 2.198095] mmcblk0: p1 p2
[ 2.340404] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 2.348428] Indeed it is in host mode hprt0 = 00001101
[ 2.551048] usb 1-1: New USB device found, idVendor=0424, idProduct=9512
[ 2.559170] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.568668] hub 1-1:1.0: USB hub found
[ 2.574049] hub 1-1:1.0: 3 ports detected
[ 2.860568] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 2.971113] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 2.979359] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber =0
[ 2.990990] smsc95xx v1.0.4
[ 3.058407] smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at usb-bcm2708_usb- 1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:6c:9c:d7
[ 7.247849] EXT4-fs (mmcblk0p2): recovery complete
[ 7.264263] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. O pts: (null)
[ 7.275204] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 7.284222] devtmpfs: mounted
[ 7.289089] Freeing init memory: 132K
[ 8.598907] udevd[155]: starting version 175
[ 9.657613] Adafruit Industries' Raspberry Pi PWM driver v1.0
[ 9.765243] Registered led device: led0
[ 15.274661] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 15.713796] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 24.752445] smsc95xx 1-1.1:1.0: eth0: link up, 100Mbps, full-duplex, lpa 0x45 E1
[ 28.684071] Adding 102396k swap on /var/swap. Priority:-1 extents:1 across:1 02396k SS
The fbtft_device does not load, or is recognized. I really do not know where to go from here.
Below I will post my dmesg:
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.6.11+ (smc@build-ssd) (gcc version 4.5.4 20120305 (prerelease) (GCC) ) #26 PREEMPT Tue Nov 26 18:19:51 SGT 2013
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr =00c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruc tion cache
[ 0.000000] Machine: BCM2708
[ 0.000000] cma: CMA: reserved 16 MiB at 1b000000
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 114688
[ 0.000000] free_area_init_node: node 0, pgdat c055c1b0, node_mem_map c060600 0
[ 0.000000] Normal zone: 896 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 113792 pages, LIFO batch:31
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 113792
[ 0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=656 b cm2708_fb.fbheight=416 bcm2708.boardrev=0xf bcm2708.serial=0x9e6c9cd7 smsc95xx.m acaddr=B8:27:EB:6C:9C:D7 sdhci-bcm2708.emmc_clock_freq=100000000 vc_mem.mem_base =0x1ec00000 vc_mem.mem_size=0x20000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115 200 kgdboc=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 eleva tor=deadline rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 448MB = 448MB total
[ 0.000000] Memory: 432132k/432132k available, 26620k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdc800000 - 0xff000000 ( 552 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdc000000 ( 448 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0502ef4 (5100 kB)
[ 0.000000] .init : 0xc0503000 - 0xc052454c ( 134 kB)
[ 0.000000] .data : 0xc0526000 - 0xc055c9e0 ( 219 kB)
[ 0.000000] .bss : 0xc055ca04 - 0xc0605e78 ( 678 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, N odes=1
[ 0.000000] NR_IRQS:394
[ 0.000000] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4 294967ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty1] enabled
[ 0.000956] Calibrating delay loop... 697.95 BogoMIPS (lpj=3489792)
[ 0.060125] pid_max: default: 32768 minimum: 301
[ 0.060588] Mount-cache hash table entries: 512
[ 0.061383] Initializing cgroup subsys cpuacct
[ 0.061443] Initializing cgroup subsys devices
[ 0.061475] Initializing cgroup subsys freezer
[ 0.061504] Initializing cgroup subsys blkio
[ 0.061643] CPU: Testing write buffer coherency: ok
[ 0.061968] hw perfevents: enabled with v6 PMU driver, 3 counters available
[ 0.062108] Setting up static identity map for 0x3b46d8 - 0x3b4734
[ 0.063597] devtmpfs: initialized
[ 0.078685] NET: Registered protocol family 16
[ 0.085100] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[ 0.086186] bcm2708.uart_clock = 0
[ 0.087579] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.087632] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.087667] mailbox: Broadcom VideoCore Mailbox driver
[ 0.087762] bcm2708_vcio: mailbox at f200b880
[ 0.087860] bcm_power: Broadcom power driver
[ 0.087897] bcm_power_open() -> 0
[ 0.087921] bcm_power_request(0,
[ 0.588604] bcm_mailbox_read -> 00000080, 0
[ 0.588643] bcm_power_request -> 0
[ 0.588668] Serial: AMBA PL011 UART driver
[ 0.588795] dev:f1: ttyAMA0 at MMIO 0x20201000 (irq = 83) is a PL011 rev3
[ 0.915559] console [ttyAMA0] enabled
[ 0.939538] bio: create slab <bio-0> at 0
[ 0.944622] SCSI subsystem initialized
[ 0.948693] usbcore: registered new interface driver usbfs
[ 0.954298] usbcore: registered new interface driver hub
[ 0.959907] usbcore: registered new device driver usb
[ 0.966205] Switching to clocksource stc
[ 0.970502] FS-Cache: Loaded
[ 0.973686] CacheFiles: Loaded
[ 0.988862] NET: Registered protocol family 2
[ 0.994116] TCP established hash table entries: 16384 (order: 5, 131072 bytes )
[ 1.001853] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 1.008640] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.015237] TCP: reno registered
[ 1.018488] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.024380] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 1.030999] NET: Registered protocol family 1
[ 1.035878] RPC: Registered named UNIX socket transport module.
[ 1.041929] RPC: Registered udp transport module.
[ 1.046652] RPC: Registered tcp transport module.
[ 1.051395] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.058502] bcm2708_dma: DMA manager at f2007000
[ 1.063289] bcm2708_gpio: bcm2708_gpio_probe c0533d98
[ 1.068730] vc-mem: phys_addr:0x00000000 mem_base=0x1ec00000 mem_size:0x20000 000(512 MiB)
[ 1.077970] audit: initializing netlink socket (disabled)
[ 1.083574] type=2000 audit(0.940:1): initialized
[ 1.220430] VFS: Disk quotas dquot_6.5.2
[ 1.224665] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.233821] FS-Cache: Netfs 'nfs' registered for caching
[ 1.240534] NFS: Registering the id_resolver key type
[ 1.245708] Key type id_resolver registered
[ 1.249907] Key type id_legacy registered
[ 1.254341] msgmni has been set to 876
[ 1.260415] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 52)
[ 1.268149] io scheduler noop registered
[ 1.272177] io scheduler deadline registered (default)
[ 1.277411] io scheduler cfq registered
[ 1.290584] Console: switching to colour frame buffer device 82x26
[ 1.300499] kgdb: Registered I/O driver kgdboc.
[ 1.307009] vc-cma: Videocore CMA driver
[ 1.312329] vc-cma: vc_cma_base = 0x00000000
[ 1.318299] vc-cma: vc_cma_size = 0x00000000 (0 MiB)
[ 1.324933] vc-cma: vc_cma_initial = 0x00000000 (0 MiB)
[ 1.340364] brd: module loaded
[ 1.349746] loop: module loaded
[ 1.354504] vchiq: vchiq_init_state: slot_zero = 0xdb000000, is_master = 0
[ 1.363466] Loading iSCSI transport class v2.0-870.
[ 1.370647] usbcore: registered new interface driver smsc95xx
[ 1.377987] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 1.590148] Core Release: 2.80a
[ 1.594563] Setting default values for core params
[ 1.600592] Finished setting default values for core params
[ 1.812456] Using Buffer DMA mode
[ 1.816950] Periodic Transfer Interrupt Enhancement - disabled
[ 1.823941] Multiprocessor Interrupt Enhancement - disabled
[ 1.830685] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 1.836194] Dedicated Tx FIFOs mode
[ 1.841817] dwc_otg: Microframe scheduler enabled
[ 1.842234] dwc_otg bcm2708_usb: DWC OTG Controller
[ 1.848391] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1
[ 1.856897] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000
[ 1.863641] Init: Port Power? op_state=1
[ 1.868726] Init: Power Port (0)
[ 1.873229] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.881391] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 1.889876] usb usb1: Product: DWC OTG Controller
[ 1.895855] usb usb1: Manufacturer: Linux 3.6.11+ dwc_otg_hcd
[ 1.902877] usb usb1: SerialNumber: bcm2708_usb
[ 1.909405] hub 1-0:1.0: USB hub found
[ 1.914495] hub 1-0:1.0: 1 port detected
[ 1.919895] dwc_otg: FIQ enabled
[ 1.919910] dwc_otg: NAK holdoff enabled
[ 1.919918] dwc_otg: FIQ split fix enabled
[ 1.919936] Module dwc_common_port init
[ 1.920161] Initializing USB Mass Storage driver...
[ 1.926542] usbcore: registered new interface driver usb-storage
[ 1.933808] USB Mass Storage support registered.
[ 1.939745] usbcore: registered new interface driver libusual
[ 1.947029] mousedev: PS/2 mouse device common for all mice
[ 1.954560] bcm2835-cpufreq: min=700000 max=700000 cur=700000
[ 1.961660] bcm2835-cpufreq: switching to governor powersave
[ 1.968493] bcm2835-cpufreq: switching to governor powersave
[ 1.975339] cpuidle: using governor ladder
[ 1.980600] cpuidle: using governor menu
[ 1.985674] sdhci: Secure Digital Host Controller Interface driver
[ 1.992998] sdhci: Copyright(c) Pierre Ossman
[ 1.998530] sdhci: Enable low-latency mode
[ 2.040501] mmc0: SDHCI controller on BCM2708_Arasan [platform] using platfor m's DMA
[ 2.050786] mmc0: BCM2708 SDHC host at 0x20300000 DMA 2 IRQ 77
[ 2.060043] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.072630] usbcore: registered new interface driver usbhid
[ 2.079533] usbhid: USB HID core driver
[ 2.089452] TCP: cubic registered
[ 2.096177] Initializing XFRM netlink socket
[ 2.103857] NET: Registered protocol family 17
[ 2.109729] Key type dns_resolver registered
[ 2.116490] Indeed it is in host mode hprt0 = 00021501
[ 2.125422] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
[ 2.151277] registered taskstats version 1
[ 2.158456] Waiting for root device /dev/mmcblk0p2...
[ 2.171110] mmc0: new high speed SDHC card at address 0007
[ 2.190541] mmcblk0: mmc0:0007 SD16G 14.9 GiB
[ 2.198095] mmcblk0: p1 p2
[ 2.340404] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 2.348428] Indeed it is in host mode hprt0 = 00001101
[ 2.551048] usb 1-1: New USB device found, idVendor=0424, idProduct=9512
[ 2.559170] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.568668] hub 1-1:1.0: USB hub found
[ 2.574049] hub 1-1:1.0: 3 ports detected
[ 2.860568] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 2.971113] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 2.979359] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber =0
[ 2.990990] smsc95xx v1.0.4
[ 3.058407] smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at usb-bcm2708_usb- 1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:6c:9c:d7
[ 7.247849] EXT4-fs (mmcblk0p2): recovery complete
[ 7.264263] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. O pts: (null)
[ 7.275204] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 7.284222] devtmpfs: mounted
[ 7.289089] Freeing init memory: 132K
[ 8.598907] udevd[155]: starting version 175
[ 9.657613] Adafruit Industries' Raspberry Pi PWM driver v1.0
[ 9.765243] Registered led device: led0
[ 15.274661] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 15.713796] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 24.752445] smsc95xx 1-1.1:1.0: eth0: link up, 100Mbps, full-duplex, lpa 0x45 E1
[ 28.684071] Adding 102396k swap on /var/swap. Priority:-1 extents:1 across:1 02396k SS
- adafruit_support_mike
- Posts: 67485
- Joined: Thu Feb 11, 2010 2:51 pm
Re: PiTFT Mini Kit - 320x240 2.8" TFT Problems
Let's try a new display..
send a note to [email protected] with a link to this thread and the folks there will get you a replacement.
send a note to [email protected] with a link to this thread and the folks there will get you a replacement.
Forum rules
Talk about Adafruit Raspberry Pi® accessories! Please do not ask for Linux support, this is for Adafruit products only! For Raspberry Pi help please visit: http://www.raspberrypi.org/phpBB3/
Talk about Adafruit Raspberry Pi® accessories! Please do not ask for Linux support, this is for Adafruit products only! For Raspberry Pi help please visit: http://www.raspberrypi.org/phpBB3/