Hi guys
i'v done the circuitbemders mod for my sh101.
after i finished my SH101 went crazy
http://www.circuitbenders.co.uk/Circuit ... 1guide.pdf
i didnt do the novamod cause it was a bit complicated without the pics like in circuitbemders
the problems are..
it doesn't sound like FM at all..
when the all the SH101 VCO slide pots all the way down i still hear sounds cause of the FM amount pot is up, as i switch the pot switch the sound changes to what it should be (sqr, saw, sub snd so..).
i dont think it suppose to play any sound when the FM amount pot is up..?
this is what i did...(i put the spst switch off, i wanted only the amount to be the on or off)
did i'v done this mode correctly?
Need help - SH101 circuitbemders (off topic)
Moderators: altitude, adafruit_support_bill, adafruit, phono, hamburgers
Please be positive and constructive with your questions and comments.
-
- Posts: 3155
- Joined: Fri Feb 17, 2006 5:35 am
Re: Need help - SH101 circuitbemders (off topic)
as best i can tell
it looks like you did it right
it looks like you did it right
- isak
- Posts: 835
- Joined: Wed May 27, 2009 3:54 pm
Re: Need help - SH101 circuitbemders (off topic)
thanks guest.
so i wonder ...mmm what the hell went wrong?
so i wonder ...mmm what the hell went wrong?
-
- Posts: 3155
- Joined: Fri Feb 17, 2006 5:35 am
Re: Need help - SH101 circuitbemders (off topic)
how loud is the sound from the fm control
i could imagine there being some bleed through
i could imagine there being some bleed through
- isak
- Posts: 835
- Joined: Wed May 27, 2009 3:54 pm
Re: Need help - SH101 circuitbemders (off topic)
i think its the non so quality pots
when i play with the wires that connected to the pots the sound is gone and back gone and back, like there is a connection and no connection..
i tried lin pot and it was ok, but for this mod i need a log pot and i dont have them now
every log pot i'v got here is bad
i will order some Alphas or if any one here have some spares Alphas 100k log pots i'll be happy to buy them from you!
when i play with the wires that connected to the pots the sound is gone and back gone and back, like there is a connection and no connection..
i tried lin pot and it was ok, but for this mod i need a log pot and i dont have them now
every log pot i'v got here is bad
i will order some Alphas or if any one here have some spares Alphas 100k log pots i'll be happy to buy them from you!
- isak
- Posts: 835
- Joined: Wed May 27, 2009 3:54 pm
Re: Need help - SH101 circuitbemders (off topic)
Hi guest.
i replaced all pots now its ok, but still i dont get the FM sound i was looking for.
it seams that the FM amount pot acts as a filter pot and not as an amount.
the pot center pin connected to this junction..
when the FM amount pot is all the down i get no sound at all, only when its up i get sound but not pure sew or pure sqr its dirty, not dirty as in ground problem or bleeds ...dirty as in sort of effect..and not FM ..
when i heard the effect at circuit-benders i wend crazy and the effect does not sound even close.
u can check it here : (roll dont a bit, their is 4 sound samples, please listen to the first one from the left till the end, this is FM!)
http://www.circuitbenders.co.uk/synthmod/SH101.html
i replaced all pots now its ok, but still i dont get the FM sound i was looking for.
it seams that the FM amount pot acts as a filter pot and not as an amount.
the pot center pin connected to this junction..
when the FM amount pot is all the down i get no sound at all, only when its up i get sound but not pure sew or pure sqr its dirty, not dirty as in ground problem or bleeds ...dirty as in sort of effect..and not FM ..
when i heard the effect at circuit-benders i wend crazy and the effect does not sound even close.
u can check it here : (roll dont a bit, their is 4 sound samples, please listen to the first one from the left till the end, this is FM!)
http://www.circuitbenders.co.uk/synthmod/SH101.html
- isak
- Posts: 835
- Joined: Wed May 27, 2009 3:54 pm
Re: Need help - SH101 circuitbemders (off topic)
its working !!!
i was not notice that it said to put the reso slide pot up..
thanks guest for trying to help me !!!
cheers,
Isak E.
i was not notice that it said to put the reso slide pot up..
thanks guest for trying to help me !!!
cheers,
Isak E.
Please be positive and constructive with your questions and comments.